Відео

Laila View

These need to be rebuildable. When they stop working there is no way to remove besides cutting them off.

Cómo se llama esa llave que se utilizaf

According to Murphy's Law a shut off valve can be relied on for many years until a few moments before you actually need it.

plumbers charge almost 3x the cost of the water heater to install what you talm bout

Asi es gracias

Cuándo la manguera dobla hay fuga porqué aunque tenga suficiente cinta teflón a que se debe

------Extremely Helpful Thank you for easy Video Boston ❤️ Massachusetts

No ma muy bien esplicado😮

I tried this, and it didn't work. My faucet still leaks.

Muy claro su vídeo, muchas gracias

Como se llaman las herramientas para aflojar la tuerca

Muy buen aporte. Espero solucionar mi grifo y ahorrarme dinero.

Thank you so much 😊 very helpful and short video straight to point ☘️

¿Cual es la medida para desenroscar?

Buenas noches cual es el numero de la llave tubo para válvula de ducha ???? 0:28

Buenas noches cual es el numero de la llave tubo para válvula de ducha ????

Buenas noches cual es el numero de la llave tubo para válvula de ducha ????

I'm just trying to figure out how to take the wrench out after 😅

I was doing it the same way, but how come it doesn't hold firm but keeps sliding?

Use a ball valve. Do not use the ones shown. The ones shown will not last.

It didn’t help at all.

Wow you skipped over the only part I needed. Removing the old valve. Thanks

Wow you skipped over the only part I needed. Removing the old valve. Thanks

Can I install without shut off main water ?

Well done, thanks

Thank you so much.

Not just to nit-pick... I'd like to point out an inconsistency that may be important. It may lead to installers to overtighten the threaded connections. Starting at 1:58, after hand-tightening the threaded connection, the narrator says to "wrench tighten another 1 to 1-1/2 turns". The demonstration shows the installer using the wrenches to tighten only about 2-1/2 hex flats past hand tight. That's less than 1/2 turn. Starting at 2:16, the video demonstrates wrench tightening the other threaded connection. Again, it appears to be a little less than 1/2 turn- no where near 1 to 1-1/2 turns past hand tight. Thank you for making this otherwise helpful video available.

Estais hechos vosotros buenos conectores flexibles de agua...en mi mundo,siempre fueron latiguillos(diferentes pulgadas)pero latiguillos de fontanería.De nada.

No plumbing tape???

If I'm replacing an existing shutoff valve, do I need to deburr and cut the pipe? I don't have much pipe to work with.

🔥👨‍🔧👍

Quel est son prix

HA! I too came here because I cannot get the valve to release. 100% followed instruction and used the mentioned tool, but the thing will simply not budge. So glad I decided to test it on a spare segment of 1/2 cooper rather than the actual line. (I won't mention their well-known competitor for this "push to connect" line, but they come off properly with the tool every time.)

hard to see

Yea some of these are faulty right off the shelf. Ive had 2 that would shut off at normal gas flow to a water heater.. i know you have to get the ones rated with the btu within range ive also just had my second one that wont reset.. i was testing by opening the gas valve with it not connected and it clicked stopping gas flow but when unscrewing from the valve equalizing the pressures on both sides of the shutoff ive had 2 now that didnt reset.. even if i back pressured the shutoff it wont reset.. the hell.?! I’m going to have to drillit out in order to give this person hot water until i go back to the warehouse and get them another one.. come on watts.. especially on safety valves.. quality control..

Alguien sabe el numero del cubo para la llave quiero conprar un cubo pero nose que numero es para la llave de la ducha

6

Thank You

Dios te bendiga

Gracias tengo 67 años y lo pude cambiar mi manguera de abasto

bon travaillé

Thank you

Internal pipe wrench is way better for this application

Sorry, but the video title says 'how to add MORE than ONE' outlet but you added only one. How to add two or three ?

Fantastic 🎉 I have had one in my shop since my pops died and now I know how to use it correctly. I need to use it now on my bathroom faucet 😂 thanks

Gracias, que instructivo. ..

Tightening only 1/2 a turn will leak for sure

great video thank you

It looks like the first adapter is BrassCraft CT2-666X-P Home Depot doesn't seem to carry the BrassCraft instead they have Everbilt Model # EBTF38 Store SKU # 367960. There are several dual stop models: sweat; threaded; dual stop/dual shut off; chrome; brass... Here are some model numbers: BrassCraft Dual Angle Supply Stop threaded R1701LRX-C1; Sweat R1901LRX-C1; Home Depot Dual Stop/Dual Shut off Model # KTCR1901DVSX R Store SKU # 1000680900. For more options Google "3/8 Water Supply Adapter T" and "Water supply dual stop".